Welcome to LIGHT Forum.......The place to be.......Enjoy your stay and have fun ....

Announcement

Collapse
No announcement yet.

Installing Enigma2 Using Spark Plugin In Amiko Alien/Alien2=STi7111/7162

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Installing Enigma2 Using Spark Plugin In Amiko Alien/Alien2=STi7111/7162

    Installing Enigma2 Using Spark Plugin In Amiko Alien/Alien2=STi7111/7162


    Do you have E2 in your Alien/Alien2 (STi 7111/7162)? If not, just in case one hasn't yet made it dual boot with Enigma2, here it is, thanx to @popssad (edited a bit by me, gorski):

    INSTALLING ENIGMA2 USING SPARK PLUGIN IN AMIKO ALIEN/ALIEN 2

    Preparation:

    USB stick formatted to FAT32
    Spark Mini Plugins pack for the Amiko Alien/Alien 2 (attached)
    Enigma2 Firmware for the Amiko Alien/Alien 2, say here: http://www.pur-e2.club/OU/images/ind...dir=6.5/fulan/

    1) Download the Plugin Pack (and much more) here: https://amikoreceiver.com/tools-for-...amiko-plugins/ or see attached.

    2) Insert a USB stick into your computer, open the Plugin Pack file you just downloaded and extract the complete plugin directory from the .zip or .rar file to the root of the USB stick (which must have been pre-formatted to FAT 32).

    3) Now, safely remove the USB stick from your computer and with your Amiko Alien/Alien 2 receiver powered on and connected to your TV, insert the USB stick into a USB port on Amiko Alien/Alien 2 (either front or rear USB port will work in the case of the Alien 2 - just ensure you have no other USB devices connected at the time).

    4) Within a few seconds the Amiko Alien/Alien 2 receiver will read the USB stick and then automatically prompt you on-screen saying ‘Confirm Do you want to upgrade plug in?’ – Select YES using the remote control arrow keys and then press OK on the remote control. This will now display the ‘Upgrade from USB’ menu and the update will start automatically which will only take a few seconds and once complete will automatically reboot your receiver. At the point of reboot you can now remove the USB stick from the Amiko Alien/Alien 2 (if you don’t then the receiver will keep prompting to update after each reboot - you can just click no though if you wish).

    5) When your Amiko Alien/Alien 2 receiver has finished booting back up you should now be back to the usual Spark firmware but there we'll now have several plugins that have been installed which can all be found by selecting MENU > Plugin using the remote control.

    At this point you are now half way there, we have all the tools required to install Enigma2 firmware via Spark so we just need to get the Enigma2 firmware itself.

    6) Download and save your required Enigma2 firmware of your choice for Amiko Alien/Alien 2 to your computer.

    7) Insert a USB stick into your computer, open the Enigma2 firmware file you just downloaded and extract the two files from the .zip or .rar file to the root of the USB stick (which must have been pre-formatted to FAT 32). These files will be named uImage and e2jffs2.img.

    8) Now remove the USB stick from your computer and with your Amiko Alien/Alien 2 receiver powered on and booted to Spark and connected to your TV, insert the USB stick into a USB port on Amiko Alien/Alien 2 (either front or rear USB port in the case of the Alien 2).

    9) Within a few seconds the Amiko Alien/Alien 2 receiver will read the USB stick. After a few seconds using the remote control go to MENU > Plug in > plugin_e2upgrade.s and while this is highlighted press the OK button which should take you straight to the Enigma2 Update menu.

    10) Make sure the Update path is showing as /storage/c/ (provided the two files were saved to the root of your USB stick) and then press RED (Enigma2 Update). You should see a pop up on-screen re. updating Enigma2, warning you not to power off the receiver (this is all automated functions and messages – you don’t need press and keys at this point).

    11) After a short while the message will disappear and you will be returned back to the Enigma2 Update menu – at this point you are actually finished and Enigma2 is now flashed, so you can exit all menus and reboot the receiver.

    12) To make the receiver boot into Enigma2 mode

    -power down the receiver at the back switch and then
    -power up the receiver again
    -while pressing and holding the OK button on the front of the receiver,
    -until FORCE is shown on the front screen, then
    -press the down arrow (to see Enigma2) on the front of the receiver and then
    -press OK.

    Your Amiko Alien/Alien2 will then boot into Enigma2 and it will boot to this mode each time as default!

    13) To change back to Spark as the default

    Basically, the reverse procedure should be done now. Using the FORCE function during the booting up, make the receiver boot into Spark mode:

    -press and hold the OK button on the front of the receiver,
    -until FORCE is seen on the front screen, then
    -press the up arrow (Spark) on the front of the receiver and then
    -press OK on the front of the receiver.

    ==============Mutiple Enigmas2 in your Alien/Alien2 using Image Manager=============

    Once you have Enigma2 image in Alien2 flash - you can do this: Image Manager for multiboot in SH4 STBs

    Using this excellent plugin one can install 3 - 4 images on a USB stick easily.

    The other USB port one can use for the external, USB connected HDD.

    Enjoy!

    gorski
    Attached Files
    Last edited by gorski; 13-12-2020, 17:56.
    sigpicI did it my way
Working...
X